Miceand Touchpads


Try going back a driver version, or so, the last update I tried sorting out my arty friend’s setup wasn’t a good one. Searched for ages to find a driver for my giant wacom UDR on Vista Please login or register. No, create an account now. I downloaded drivers for some of the new hardware with the same UD series but when it tries to scan for port 3 the installer just stop and freezes. How can this be resolved. Jul 16, Messages:

Uploader: Akigore
Date Added: 23 October 2013
File Size: 21.34 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 16069
Price: Free* [*Free Regsitration Required]

This is also assuming that you are looking at the female end of the serial connector as if you ud-0608r the male side, just to clarify not sure if that’s how it should have been read an obviously U-d0608-r matched the written info off the PCB to come to my conclusions and the MC is placed there exactly as it is on the board, writing is oriented the way I looked down at it from above. I cut the leg in the mod because I figured it is safer and probably more “valid” electronically.

wacom digitizer 2

It is in approximately the same family as the SD that I bought off of ebay. I already have some good no clean lead free flux and one last question the copper tape plugging very specific holes if some of the adhesive is coming off how do I put it back I am assuming those holes are covered with special tape for a reason?

But yes, the numbers matches exactly with the UDR — so we can proceed with the same mod! I have several of the original pens but not sure if they will work here. And you can get it here: Hey here are the images Bernard the realterm does not work on 64bit win and putty cant read the serial port maybe the virtual port is the reason ill figure it out somehow all it says is digitizer Ii and the voltage on the bottom I looked all over inside the only sticker i found inside was a barcode sen-a this is below the sen number 6lwc and one other and one is dk6 EDIT: Thanks you’ve been great Bernard!


Ask Talk to Expert.

Mar 19, Messages: Please enter a valid email address. Try going back a driver version, or so, the last update I tried sorting out my arty friend’s setup wasn’t a good one.

Converting Wacom UDR from Serial to USB

Can’t offer much more, as the friend who used this sadly passed away a few months ago. I think you can aslo buy a Yd-0608-r card for your computer and skip the serial-usb adapter since Vista doesn’t support the adapter for Wacom tablets.

My Wacom Tablet won’t recognize the pen. No, create an account now.


Does the driver on the Wacom site work? Ok so going to get busy on this, and since everything is the same on this board that is a good thing Add Your Answer Tips for a great answer: The DB9 connector is the serial port connector 9 pins wackm is meant to connect to the computer — the one at the end of the cable.

The most important ones are Pin 2 and Pin 3 but you have to look for the others as well. Sometimes that does work, so no harm in trying. Bongofish November 08,uud-0608-r June 23, The hope is that the mapping is the same for the UDR. All Wacom boards I have seen do that: Wwacom what is the range of resistance on something like this what range of ohms should my meter be on, and if you do not mind, just a quick little explanation of which pins I should be testing since the boards are entirely different and I have never worked with a circuit board like this, in the automotive industry we check for resistance range which changes the signal of a sensor and the like, such as when you press the accelerator pedal the resistance gets higher eacom lower which is how udd-0608-r computer tells what percentage of pedal that you are pressing and therefore knows what stage the throttle is in, is this how the pressure sensitivity works on the tablet?

New Drivers  DRIVER: TRAVELMATE 6593

I did that for the UDR already. I attach one of the probe to that wire and then I slowly “scan” the pins on the chip to discover which one is connected to it if any. This board will not “really” become an intuos! Are you a Wacom Computer and Internet Expert? I tried to take the nasty light out of the waclm but wcaom is my tool and with it not working correctly right now i had to default to an inferior editing tool.

Make sure you remove any other Wacom drivers, tablet, and reboot. I did not realize how terrible those images were until I saaw this one Here’s a link to this great service Good luck!